I think it is probably kind of self explanatory from the video what I will be trying to do or test here:
In general, Peltier devices are considered very inefficient when used for refrigeration, mostly due to the fact that for a refrigerator the device is trying to pull heat from a cold refrigerator or ice box, which is very difficult due to there being very little heat in the ice compartment, for the Peltier device to move, so the colder the refrigerator gets the harder the Peltier device has to work and so the efficiency goes down very quickly.
However, apparently a Peltier device will ALWAYS be more than 100% efficient when used as a HEATER because ALL of the electricity used to run the Peltier device is transformed into heat, and then the chip will also MOVE at least SOME environmental heat as well, so you get all the electrical energy back as heat as well as whatever additional energy the chip is able to move through itself from the environment, which under some circumstances can be considerable; comparable with the COP of a conventional Heat Pump.
Anyway, the heat (and/or cold) generated from a Peltier device can run a Stirling engine. Here is a video of two Stirling engines operating simultaneously, one on the cold side and one on the hot side of a single Peltier unit:
My idea is to use a magnet as a piston to turn the Stirling engine into a linear generator to produce the electricity to run the Peltier "HEAT PUMP" to MOVE heat and generate heat to power the Stirling engine.
The big heat sink is NOT to keep the Peltier device cool, but rather to keep the COLD SIDE of the Peltier device WARM; close to ambient temperature.
From what I understand, or have been reading about these devices, keeping the cold side of a Peltier warm when it is being used as a heater, will increase the COP considerably.
Anyway, it is a relatively easy and inexpensive experiment, so why not give it a try, right?
From the way it sounds, the main problem might be preventing the Peltier chip from getting TOO HOT and burning itself up.
The Engineer Horvath had 3 related Patents for hydrogen from water auto conversions. Final cell as low voltage , another at high voltage with same instilled circuit, and the more elaborate water cell with central radiation Magnetron tube.Photos do not tell which type was displayed. I studied the low volts model and typed out page of proof reading errors not caught .Patents designs included obvious non essential parts to deter people from replication, - such as cast special carburetor, large diameter cell, interior - rather than external transformer.
Outer box strong magnets on sides of narrow cell would suffice to speed ions . I had 2 steel plates knurled rough with matching flutes nickel plated at machine shop.. They would face each other in narrow gap. High temp gray PVC plates measured for cell + removable cover. Source for free distilled water would still be needed.
John Keely did science experiments in late 1800's and floated a few heavy weights as brass and steel. he used frequencies applied with ratios on wires we now call thermocouples and thermopiles. Wires as platinum, gold + silver , as due to resistance matching ratios. Heavy platform of 3 brass flywheels as sirens were also operated with air pressure to speed up to certain tones. Keely was musician and knew sounds. with tones change by ratio, along with mass chord, the whole unit would rise up and settle down with air withdrawn. A modern test of one thermocouple on digital weigh scales showed loss of weight, by itself. Documents available from Mr. Pond of S.V.P. I studied Keely for 8 1/2 years with about $500 in old papers.
Controlled remote flying generator was done by Mr. Searl. It was a combination of rotating magnetic field and high volts electrical field same time. Silent, as no air at edge of hull rim was vacuum to pass no sound waves.
Also Russian entomologist made floating contraption he stood on by high volts field over tiny cavity resonators on lower board. The tiny pores cause disruption of gravity waves emanating from ground. Anything above had no weight.
French scientist had local newspaper article (translated from Babblefish) of floating open frame dirigible using sandwich plates of thermocouple at each end and excited by frequency generator signals. Device flown to next town and back.
The late Mr. Baumgartner demonstrated a vortex swirl of air unit, low power, that that tapped into the ETHER field. Any weight , including him , and front end of city bus, on plywood form with small motor at high speed turning small turbine. The armature winding connections was changed from parallel to series to get a higher RPM. There are 3 types of spirals, - guess which one it was!
This is a build log, please do not sidetrack this thread with different views. If you have different views, please open a new thread of use another existing thread.
I found a way to make unlimited AC phases. I'll be posting more about that soon.. For now- I need to log this data on phase peak voltages.
8 Phase
Phase 1 (0°): 10.000000 V
Phase 2 (45°): 7.071068 V
Phase 3 (90°): 0.000000 V
Phase 4 (135°): −7.071068 V
Phase 5 (180°): −10.000000 V
Phase 6 (225°): −7.071068 V
Phase 7 (270°): 0.000000 V
Phase 8 (315°): 7.071068 V
16 Phase
Phase 1 (0°): 10.000000000 V
Phase 2 (22.5°): 9.238795325 V
Phase 3 (45°): 7.071067812 V
Phase 4 (67.5°): 3.826834324 V
Phase 5 (90°): 0.000000000 V
Phase 6 (112.5°): −3.826834324 V
Phase 7 (135°): −7.071067812 V
Phase 8 (157.5°): −9.238795325 V
Phase 9 (180°): −10.000000000 V
Phase 10 (202.5°): −9.238795325 V
Phase 11 (225°): −7.071067812 V
Phase 12 (247.5°): −3.826834324 V
Phase 13 (270°): 0.000000000 V
Phase 14 (292.5°): 3.826834324 V
Phase 15 (315°): 7.071067812 V
Phase 16 (337.5°): 9.238795325 V
24 Phase
Phase 1 (0°): 10.000000000 V
Phase 2 (15°): 9.659258263 V
Phase 3 (30°): 8.660254038 V
Phase 4 (45°): 7.071067812 V
Phase 5 (60°): 5.000000000 V
Phase 6 (75°): 2.588190452 V
Phase 7 (90°): 0.000000000 V
Phase 8 (105°): −2.588190452 V
Phase 9 (120°): −5.000000000 V
Phase 10 (135°): −7.071067812 V
Phase 11 (150°): −8.660254038 V
Phase 12 (165°): −9.659258263 V
Phase 13 (180°): −10.000000000 V
Phase 14 (195°): −9.659258263 V
Phase 15 (210°): −8.660254038 V
Phase 16 (225°): −7.071067812 V
Phase 17 (240°): −5.000000000 V
Phase 18 (255°): −2.588190452 V
Phase 19 (270°): 0.000000000 V
Phase 20 (285°): 2.588190452 V
Phase 21 (300°): 5.000000000 V
Phase 22 (315°): 7.071067812 V
Phase 23 (330°): 8.660254038 V
Phase 24 (345°): 9.659258263
32 Phase
Phase 1 (0.00°): 10.000000000 V
Phase 2 (11.25°): 9.807852804 V
Phase 3 (22.50°): 9.238795325 V
Phase 4 (33.75°): 8.314696123 V
Phase 5 (45.00°): 7.071067812 V
Phase 6 (56.25°): 5.555702330 V
Phase 7 (67.50°): 3.826834324 V
Phase 8 (78.75°): 1.950903220 V
Phase 9 (90.00°): 0.000000000 V
Phase 10 (101.25°): -1.950903220 V
Phase 11 (112.50°): -3.826834324 V
Phase 12 (123.75°): -5.555702330 V
Phase 13 (135.00°): -7.071067812 V
Phase 14 (146.25°): -8.314696123 V
Phase 15 (157.50°): -9.238795325 V
Phase 16 (168.75°): -9.807852804 V
Phase 17 (180.00°): -10.000000000 V
Phase 18 (191.25°): -9.807852804 V
Phase 19 (202.50°): -9.238795325 V
Phase 20 (213.75°): -8.314696123 V
Phase 21 (225.00°): -7.071067812 V
Phase 22 (236.25°): -5.555702330 V
Phase 23 (247.50°): -3.826834324 V
Phase 24 (258.75°): -1.950903220 V
Phase 25 (270.00°): 0.000000000 V
Phase 26 (281.25°): 1.950903220 V
Phase 27 (292.50°): 3.826834324 V
Phase 28 (303.75°): 5.555702330 V
Phase 29 (315.00°): 7.071067812 V
Phase 30 (326.25°): 8.314696123 V
Phase 31 (337.50°): 9.238795325 V
Phase 32 (348.75°): 9.807852804 V
40 Phase
Phase 1 (0.00°): 10.000000000 V
Phase 2 (9.00°): 9.876883406 V
Phase 3 (18.00°): 9.510565163 V
Phase 4 (27.00°): 8.910065242 V
Phase 5 (36.00°): 8.090169944 V
Phase 6 (45.00°): 7.071067812 V
Phase 7 (54.00°): 5.877852523 V
Phase 8 (63.00°): 4.539904997 V
Phase 9 (72.00°): 3.090169944 V
Phase 10 (81.00°): 1.564344650 V
Phase 11 (90.00°): 0.000000000 V
Phase 12 (99.00°): -1.564344650 V
Phase 13 (108.00°): -3.090169944 V
Phase 14 (117.00°): -4.539904997 V
Phase 15 (126.00°): -5.877852523 V
Phase 16 (135.00°): -7.071067812 V
Phase 17 (144.00°): -8.090169944 V
Phase 18 (153.00°): -8.910065242 V
Phase 19 (162.00°): -9.510565163 V
Phase 20 (171.00°): -9.876883406 V
Phase 21 (180.00°): -10.000000000 V
Phase 22 (189.00°): -9.876883406 V
Phase 23 (198.00°): -9.510565163 V
Phase 24 (207.00°): -8.910065242 V
Phase 25 (216.00°): -8.090169944 V
Phase 26 (225.00°): -7.071067812 V
Phase 27 (234.00°): -5.877852523 V
Phase 28 (243.00°): -4.539904997 V
Phase 29 (252.00°): -3.090169944 V
Phase 30 (261.00°): -1.564344650 V
Phase 31 (270.00°): 0.000000000 V
Phase 32 (279.00°): 1.564344650 V
Phase 33 (288.00°): 3.090169944 V
Phase 34 (297.00°): 4.539904997 V
Phase 35 (306.00°): 5.877852523 V
Phase 36 (315.00°): 7.071067812 V
Phase 37 (324.00°): 8.090169944 V
Phase 38 (333.00°): 8.910065242 V
Phase 39 (342.00°): 9.510565163 V
Phase 40 (351.00°): 9.876883406 V
SpacePropulsionA is based on (resultant force from ) eddy current repulsive forces between coil and metal plate
SpacePropulsionB is based on (resultant force from ) repulsive forces between 2 Coils
Guests cannot see images in the messages. Please register at the forum by clicking here to see images.
The basic idea is to use Parallel resonance current magnifier in such a way that electrolyser cells are placed in each branch of the LC circuit.
The the current through cells will be much , compared to current from source.
I'm at a point with my generator where I've joined enough dots and the bigger picture is starting to emerge.
It all starts with the gyroscope. Joseph Newman absolutely nailed it when he correlated directional force on a gyroscope with the direction of current flow from an inductor as a mechanical function.
The significance of this is fundamental. Take a gyroscope as shown. With the rotor spinning anticlockwise (looking downward on it), rotate the gymbal clockwise. Why does it suddenly want to flip? And once flipped, you can spin it as fast as you want and it will never flip back, until you rotate the gymbal anticlockwise. Immediately the gyroscope will want to flip back. Interestingly, the faster you spin the gymble, the quicker you'll find the tipping point - but, you can rotate slowly enough (with the gyro spinning 10-12k) and not find the tipping point. There is a field that comes into being, and exists as a result of high speed rotation. Every atom in existence has the same gyroscopic field...
This field can be seen as a mechanical representation of Lenz in a single direction.
A magnet or electromagnet comprises two of these fields, because a magnetic field has both polarities at each pole (the dominant North becomes the North pole - as per Howard Johnson).
So now we better understand WHAT Lenz is. A barrier between higher and lower density energy as a result of induction.
Now to learn WHY Lenz is.
Casual mid post disclaimer - if anything, I'm wiriting this to find any holes in what I've learnt as a result of observing. And I could well have got it all wrong.
What is the first thing that occurs when a magnet approaches a cored coil? Pressure. What does pressure do? It moves things...
After everything I've acheived with my pulse motor, I still hadn't pulled out very much current. (Having said that, I made the concious decision not to mechanically switch +550V at very close proximity to Neo magnets - emulating Adams, as I had a bad experience doing so at only +300V).
So I can do pressure.
This is where it gets more difficult to explain.
We know there are fields rotating around a gyroscope, so we know there are rotating fields around a magnet (emanating from the bloch wall) - how does a coil that has just become an electromagnet deal with these rotating fields? If you're a little confused, re-read from the top or go and play with a gyroscope for a while and get the 'feel' of them... just as much fun as magnets.
Generator lag occurs at 90 degrees from the rotor is the first clue. Why 90 degrees?
This is where the pieces start to come together. As it is in a magnet, the two rotating fields around a coil exist to equalise anything that might be happening to the coil. Like throwing a magnet at it to induce current. So these two rotating fields - they spin counterclockwise looking down on the coil and spin opposite each other (like North and South, but rotating horizontally) As a magnet induces a coil, the pressure of the flux on the copper electrons causes a blockage of sorts as they resist the flux change - the rotating fields also don't like pressure and move 90 degrees either side of the oncoming flux pressure as they also need to be balanced.
The magnet now has the first half of the sine wave at max. Why does it then recede? Has the magnet stopped moving? Nope. Has the magnet stopped being able to push the initial electrons forward because at the center of the coil, the magnet is now at 90 degrees to where the rotating field had moved to, and can't push it forward anymore? Yes!! Remember what Newman showed - it is all mechanical.
So what's the fix? This is where Al Hubbard (and Tesla) come in to finish.
Putting a coil at the 90 degree mark of a primary, makes the exact same situation above happen again! Guided by Newman, and knowing that a coil induced by a field will rotate 90 degrees to equalise pressure / resist change - this is equivalent to two rotors with North facing each other and pushing away from each other - to continue the moving of the flux around the coil as the magnet passes over. So that is moving past 90 degrees to 180 degrees. I need to flip flop as the magnet is only moving in one direction, so a coil on the other side of a primary wil help that flux move the other 180 degrees around the coil.
Hubbard worked this out, and had 8 coils interacting with a central coil. Exactly the same as an alternator, whereby a constant feed is given to create a central rotating field - but in this case the field keeps moving as the surrounding coils 'mechanically' interact and constantly drive it resulting in huge current in the center as the flux is always moving. Additionally, the secondaries have a secondary winding (just like a spark plug), so that a trine of frequencies can go through a Fourier transform and become a square wave that keeps it going indefinitely.
Thank you for the oppertunity to share my thoughts.
Please take the time to view the web site explaining a basic gravitational principal overlooked for the alleged 4000 year we have been on earth. This must please be shared far and wide, it is a basic element of life and will be a game changer in the energy monopoly. https://orbitalharvester.online/
Not patented and should never be patented - the principal physics opens a new door of innovation for all those that strive to a better place to live.
